手工雕刻不锈钢钢模(钢雕印章)制作过程



instructables 上看到的一个手工制作钢模(钢雕印章的)教程,很详细。


制作钢模,真的很难,一方面是因为雕刻的过程是极度痛苦的,尤其是中文字,更会让人抓狂,其次,还需要进行淬火,这个也是非常专业的过程。


因此,不作详细说明,仅当做制作过程欣赏吧!







将手写好的印章图案,使用超级胶水和台钳,固定在蜂巢状的六角钢棒( 六边形钢棒 )上,然后使用Dremel电动工具进行雕刻,雕刻前,需要在不锈钢上敲上点或锯上线,这样电动工具才不会打滑。


整个雕刻大概花了6个小时,这是一个艰难的过程...































































雕刻完后,需要进行硬化处理,将雕刻好的印章,在200度左右的烤箱中,烤大约1.5小时,然后放进费油中进行淬火。













最后,给钢模加一个底座,让钢模更好看。

















关于作者
  • {{ comment.commentator.username
    看完后觉得还是买现成的吧
    2016-08-06 01:02
  • {{ comment.commentator.username
    200度能淬火?你这是什么钢?
    2016-08-09 19:25
  • {{ comment.commentator.username
    同想问淬火温度
    2016-08-12 20:11
  • {{ comment.commentator.username
    贵在手工啊~ 看着心太累啊
    2016-08-17 16:58
  • {{ comment.commentator.username
    @烈性酒 是啊,看着太虐了 。。。
    2016-08-18 10:54
  • {{ comment.commentator.username
    @白兔先生 @Marguerite孟清

    原文如此:

    “Re- hardening of the stamp involved re-heating the metal to transition temperature (non-magnetic) and then quenching it in water (I would have preferred using waste oil, but didn't think it would be a good idea indoors). After quenching I tested the stamp using a file for hardness to make sure the file would no longer cut the stamp, it did not cut, but rather slid over the surface removing only a small amount of scale; which put the hardness of my stamp somewhere around RC-60 or harder (hard as a transmission or rear end gear in a truck, or a metal file). Water quenching is very fast, but also puts a lot of stress in the metal, so I tempered the stamp at 400 Deg F in the kitchen oven for 1-1/2 Hrs to help relax stress in the metal or "Temper" it. I shined the stamp up with the wire brush, and moved on to the socket that held it. ”

    我仅仅只将400华氏度换成了摄氏度。
    2016-08-18 10:59
  • {{ comment.commentator.username
    @牧野工房 感觉,摄氏换成华氏还有可能。200度淬火真心是没听说过,200度的低温回火我倒是有见过。
    2016-08-18 11:20
  • {{ comment.commentator.username
    难度系数10颗星!!!
    2016-08-19 17:45
  • {{ comment.commentator.username
    @白兔先生 试试看就知道了,实践出真知。
    2016-08-20 22:18
  • {{ comment.commentator.username
    @清平 我自己经常进行热加工。在我所知道的范围里,实在是无法理解。也许美帝高精尖有如此材料吧。
    2016-08-20 23:52
  • 阿辛

kiinii帐号登录

手工艺人和设计师的兴趣分享社区

iOS、Android 均可扫码下载 APP